Body Rubber Kit
$749.99
Part #
38-0512
Application
E-Type Ser. 2 OTS
Save 10% off individual prices when you purchase the whole kit! Moss Classic Jaguar sells the most comprehensive rubber kits in the business. If you want the best kit on the market, here it is. Our kits are designed to provide everything you need for a comprehensive, bare-metal repaint. All door, boot, lamp and glass seals are included. Interior and engine compartment items are not.
Notes
1: These were fitted to the rear of later cars, but many customers prefer to fit them at all attaching points. Use as you see fit.
2: We liberally coat this and the chrome with WD40, install chrome and clamp. Trim flush the next day. The WD40 acts as a solvent to soften the rubber and ensure a tight seal. The rubber is supposed to stay soft.
3: There are two tail lamp configurations but only one gasket type is available. You may have to trim the middle to clear the bulb sockets.
4: A coupe A-Post seal is supplied. Cut for roadster.
5: A couple windshield is supplied. Cut for roadster.
6: Does not have pre-drilled holes. Holes for attaching rivets must be cut by customer.
Also note that you might not receive one continuous piece of rubber in some cases where the items is sold per foot. You might receive two pieces at least five feet long when the car requires a total of ten feet.
Part Number | Description | Qty Per Kit | Notes |
---|---|---|---|
BD18947/3 | BUMPER SEAL, FRONT | 2 | Between front bumpers and body; clips retain ends |
BD10313 | CLIP, BUMPER and WINDOW SEAL | 14 | Secures front bumper-to-body seal (4) and door squeege seal (14) |
BD28523 | RUBBER BUFFER | 8 | Square rubber pad, between body and front bumper brackets (see Note #1) |
BD21800 | TOP SIDE SEAL | 2 | Glued to top frame in one piece and then cut at joints |
BD22536 | GAS LID BUFFER | 2 | Small rubber buttons to cushion gas filler lid |
BD24789 | SILL SEAL | 2 | At bottom of door openings, proper molded type; glued in place |
BD25715/1 | TRUNK SEAL | 1 | Around perimeter of trunk/boot opening; pushes on |
BD25898/99 | SEAL, SHUT POST | 1 PR | Door jamb at rear, glued in channel; proper molded in top curve |
BD33326/1 | "EVERSEAL" STRIP | 1 | Seals joint between windshield glass and chrome (See Note #2) |
BD35733 | MARKER GASKET, REAR | 2 | Between rear side marker lamps and body |
BD35977/1 | BUMPER SEAL, REAR | 1 | Between rear bumper and body |
BD37726 | MARKER GASKET, FRONT | 2 | Between front side marker lamps and body |
BD37782-1 | TOP-TO-WINDSCREEN SEAL | 1 | Seals top frame to top of windscreen |
BD38155 | LAMP PAD, RH | 1 | Rubber between tail lamp and body (See Note #3) |
BD38156 | LAMP PAD, LH | 1 | Rubber between tail lamp and body (See Note #3) |
12339 | LAMP GASKET | 1 | Between license lamp housing and license lamp lens |
159-110 | LAMP GASKET | 4 | Seals reverse lamp lenses and reverse lamp body |
209 | OVER RIDER SEAL | 8 | Between bumper over riders and bumpers |
164-060 | HEADLAMP GASKET | 2 | Seals headlamp unit to body |
BD20903/1 | COWL SEAL | 1 | Cushions rear edge of bonnet, glued into channel near base of windshield |
12426 | LENS PAD, TURN SIGNALS | 2 | Pad between turn signal lenses and turn signal lamp body |
8608-2L | LAMP PAD, LH | 1 | Gasket between front turn signal lamp and body, left |
8608-2R | LAMP PAD, RH | 1 | Gasket between front turn signal lamp and body, right |
38-2008 | FOAM LENS PAD | 2 | Foam pad between tail lamp lenses and tail lamp bodies |
BD25716/7 | A-POST SEAL, PAIR | 1 PR | Major seal for leading edge of doors; glued to body (See Note #4) |
BD20499 | WINDSHIELD SEAL | 1 | Holds windshield in place -- requires locking strip below (See Note #5) |
BD20499-1 | W/S LOCK STRIP | 11' | Fits in channel of windshield seal; expands it to make tight seal |
38-2020 | CHANNEL FELT | 8' | For door glass channels. Push in to channels and trim flush. |
38-2024 | DOOR FRAME RUBBER SEAL | 3' | Leading edge of door frame; fits in channel; 1.5' required per side. |
11728 | LENS GASKET | 4 | Seals side marker lenses to chrome lamp housings |
BD35729 | HEADLIGHT RUBBER | 2 | Between body and headlamp opening finishers (See Note #6) |
BD16700 | WINDOW SEAL | 2 | Squeegee seal; between door and outer surface of door glass. Clips in place |
BD20010/3 | 24" FUZZY STRIP | 2 | Fuzzy seal; between door and inner surface of door glass, clips in place |
BD22312 | CLIP FOR FUZZY STRIP | 10 | Attaches fuzzy window seal; five per side |
8656 | BEZEL PAD | 3 | Under chrome windshield wiper bezels |
BD20434 | MUDSHIELD SEAL | 7' | Mud shields under bonnet; riveted in place |
Notes
1: These were fitted to the rear of later cars, but many customers prefer to fit them at all attaching points. Use as you see fit.
2: We liberally coat this and the chrome with WD40, install chrome and clamp. Trim flush the next day. The WD40 acts as a solvent to soften the rubber and ensure a tight seal. The rubber is supposed to stay soft.
3: There are two tail lamp configurations but only one gasket type is available. You may have to trim the middle to clear the bulb sockets.
4: A coupe A-Post seal is supplied. Cut for roadster.
5: A couple windshield is supplied. Cut for roadster.
6: Does not have pre-drilled holes. Holes for attaching rivets must be cut by customer.
Also note that you might not receive one continuous piece of rubber in some cases where the items is sold per foot. You might receive two pieces at least five feet long when the car requires a total of ten feet.
Note: This item replaces part number 18-0512.
Model (Site) | Category | Schematic | Key | Name | Application | Qty |
---|---|---|---|---|---|---|
Jaguar E-Type | Body Fittings | Body Rubber Kits | 1 | BODY RUBBER KIT | E-Type Series II OTS | 1 |
The Longest in the Business
- All Classic British products are warrantied to be free from defects in material and workmanship for 2 years from the date of invoice.
- All superchargers, supercharger components, and supercharger hardware are warranted to be free from defects in material and workmanship for 1 year from date of invoice.
- Moss Motors, Ltd. will, at its discretion, repair or replace any part that fails in service within the warranty period. This warranty does not cover labor, failure of related components, normal wear of brake or clutch components or failure resulting from alteration, misuse, accidental damage, faulty installation, or faulty repair.
- Warranty requests should be submitted to our sales department and must be supported by the original Moss Motors purchase invoice and documentation of the failure.
Product Name:
Body Rubber Kit
Make:
Jaguar
Model:
E-Type
Year:
1969, 1970, 1971