Body Rubber Kit
$719.99
Part #
38-0515
Application
E-Type Ser. 3 OTS, 1971-73
WARNING: May contain chemicals that may cause cancer or reproductive harm.
Save 10% off individual prices when you purchase the whole kit! Moss Classic Jaguar sells the most comprehensive rubber kits in the business. If you want the best kit on the market, here it is. Our kits are designed to provide everything you need for a comprehensive, bare-metal repaint. All door, boot, lamp and glass seals are included. Interior and engine compartment items are not.
Notes
1: We liberally coat this and the chrome with WD40, install chrome and clamp. Trim flush the next day. The WD40 acts as a solvent to soften the rubber and ensure a tight seal. The rubber is supposed to stay soft.
2: Three pieces supplied: two for the A-posts and a third to cut in half for the door shut face seals.
3: Does not have pre-drilled holes; installer must drill holes for attachment rivets.
| Part Number | Description | Qty Per Kit | Notes |
|---|---|---|---|
| BD10313 | CLIP | 8 | Secures front bumper seals to body |
| BD18947/3 | BUMPER SEAL, FRONT | 2 | Between front bumpers and body |
| BD18947/4 | BUMPER SEAL, REAR | 1 | Between rear bumper and body |
| BD21073/4 | WINDOW WIPE | 2 | Outer squeegee seal, door glass |
| BD22312 | CLIP | 10 | Secure door glass "fuzzy strips" to upper door |
| BD22536 | GAS LID BUFFER | 2 | Small rubber buttons to cushion gas filler lid |
| BD25715/1 | TRUNK SEAL | 1 | Around perimeter of trunk/boot opening; pushes on |
| BD28447/1 | LWB SILL SEAL | 2 | At bottom of door openings, proper molded type; glued in place |
| BD28523 | RUBBER BUFFER | 6 | Between front (4) and rear bumpers (2) and body |
| BD33326/1 | "EVERSEAL" STRIP | 1 | Seals joint between windshield glass and chrome (See Note #1) |
| BD35733 | MARKER GASKET, REAR | 2 | Pad between body and side marker lamp |
| BD37726 | MARKER GASKET, FRONT | 2 | Pad between body and side marker lamp |
| BD37782-1 | TOP-TO-WINDSCREEN SEAL | 1 | Seals top frame to top of windscreen |
| BD38155 | LAMP PAD, RH | 1 | Tail Lamp Unit to Body, Right |
| BD38156 | LAMP PAD, LH | 1 | Tail Lamp Unit to Body, Left |
| 12339 | LAMP GASKET | 1 | License lamp lens gasket |
| 159-110 | LAMP GASKET | 4 | Reverse lamp lens and body gasket |
| 209 | OVER RIDER SEAL | 6 | Rubber between bumper over riders and bumper blades |
| 164-060 | HEADLAMP GASKET | 2 | Head lamp bucket to body |
| 38-1500 | WINDOW SEAL | 6' | Top frame to side window |
| BD20903/1 | COWL SEAL | 1 | Cushions rear edge of bonnet, glued into channel near base of windshield |
| 12426 | LENS PAD, T/S | 2 | Front turn signals lenses to lamp bodies, same right or left |
| 8608-2L | LAMP PAD, LH | 1 | Front turn signal lamp unit to body, left |
| 8608-2R | LAMP PAD, RH | 1 | Front turn signal lamp unit to body, right |
| 38-2008 | FOAM LENS PAD | 2 | Tail lamp lenses to tail lamp body, same right or left |
| BD30301 | A-POST SEAL | 3 | Used on A-posts and door shut faces (See Note #2) |
| BD21964/2 | WINDOW FRAME "T" SEAL | 3 | Leading edge of door window frame |
| BD20499-1 | WINDSHIELD LOCK STRIP | 10' | Fits in channel of windshield seal; expands it to make tight seal |
| BD20499-3 | WINDSHIELD SEAL | 1 | Holds windshield in place -- requires locking strip below. |
| 38-2020 | CHANNEL FELT | 8' | For door glass channels. Push in to channels and trim flush. |
| 11728 | LENS GASKET | 4 | Side marker lenses to side marker lamp bodies |
| BD35729 | HEADLIGHT RUBBER | 2 | Under chrome finishers -- perimeter of "sugar scoops" (See Note #3) |
| BD20010/3-2 | FUZZY STRIP 32" | 2 | Inner surface of door glass |
| 8656 | BEZEL PAD | 2 | Pad under windshield washer bezels |
| BD20434 | MUDSHIELD SEAL | 8' | On mud shields under bonnet |
Notes
1: We liberally coat this and the chrome with WD40, install chrome and clamp. Trim flush the next day. The WD40 acts as a solvent to soften the rubber and ensure a tight seal. The rubber is supposed to stay soft.
2: Three pieces supplied: two for the A-posts and a third to cut in half for the door shut face seals.
3: Does not have pre-drilled holes; installer must drill holes for attachment rivets.
Note: This item replaces part number 18-0515.
| Model (Site) | Category | Schematic | Key | Name | Application | Qty |
|---|---|---|---|---|---|---|
| Jaguar E-Type | Body Fittings | Body Rubber Kits | 1 | BODY RUBBER KIT | E-Type Series III OTS, 1971-1973 | 1 |
The Longest in the Business
- All Classic British products are warrantied to be free from defects in material and workmanship for 2 years from the date of invoice.
- All superchargers, supercharger components, and supercharger hardware are warranted to be free from defects in material and workmanship for 1 year from date of invoice.
- Moss Motors, Ltd. will, at its discretion, repair or replace any part that fails in service within the warranty period. This warranty does not cover labor, failure of related components, normal wear of brake or clutch components or failure resulting from alteration, misuse, accidental damage, faulty installation, or faulty repair.
- Warranty requests should be submitted to our sales department and must be supported by the original Moss Motors purchase invoice and documentation of the failure.
Product Name:
Body Rubber Kit
Make:
Jaguar
Model:
E-Type
Year:
1971, 1972, 1973