Body Rubber Kit
$629.99
Part #
38-0518
Application
E-Type Ser. 1.5 OTS
WARNING: May contain chemicals that may cause cancer or reproductive harm.
Save 10% off individual prices when you purchase the whole kit! Moss Classic Jaguar sells the most comprehensive rubber kits in the business. If you want the best kit on the market, here it is. Our kits are designed to provide everything you need for a comprehensive, bare-metal repaint. All door, boot, lamp and glass seals are included. Interior and engine compartment items are not.
Notes
1: These were fitted to the rear of later cars, but many customers prefer to fit them at all attaching points. Use as you see fit.
2: We liberally coat this and the chrome with WD40, install chrome and clamp. Trim flush the next day. The WD40 acts as a solvent
3: A coupe A-Post seal is supplied. Cut for roadster.
4: A coupe windshield seal is supplied. Cut for roadster.
5: Does not have pre-drilled holes; customer must drill holes for attachment rivets.
| Part Number | Description | Qty Per Kit | Notes |
|---|---|---|---|
| BD10313 | CLIP | 18 | Secure front bumper rubber ends (4) and door glass squeegee strips (14) |
| BD15746 | LAMP GASKET | 2 | License Lamp, Inner |
| BD18947/1 | BUMPER SEAL, REAR | 2 | Between rear bumpers and body |
| BD18947/3 | BUMPER SEAL, FRONT | 2 | Between front bumpers and body; secured with BD10313 clips |
| BD21800 | TOP SIDE SEAL | 2 | Glued to top frame in one piece and then cut at joints |
| BD22312 | CLIP | 10 | Secures fuzzy strips on inner surface of door glass |
| BD22536 | GAS LID BUFFER | 2 | Small rubber buttons to cushion gas filler lid |
| BD25715/1 | TRUNK/BOOT LID SEAL | 1 | Pushes on to flange |
| BD24789 | SILL SEAL | 2 | At bottom of door openings, proper molded type; glued in place |
| BD25898/99 | SEAL, SHUT POST | 1 PR | Door jamb at rear, glued in channel; proper molded in top curve |
| BD28523 | RUBBER BUFFER | 8 | Square rubber pad, between body and bumper brackets (See Note #1) |
| BD33326/1 | EVERSEAL STRIP | 1 | Seals joint between windshield glass and chrome (See Note #2) |
| BD37782-1 | TOP-TO-WINDSCREEN SEAL | 1 | Seals top frame to top of windscreen |
| BD6581 | RUBBER PLUG | 4 | Seals holes behind license plate |
| 8607 | TURN SIGNAL LENS PAD | 1 PR | Pads between front turn signal lenses and lamp body |
| 8620 | REAR LENS PADS | 1 PR | Pads between rear lenses and lamp body |
| 8716 | LAMP GASKET | 1 | Gasket between reverse lamp lens and lamp body |
| 8717 | LAMP GASKET | 1 | Gasket, reverse lamp body |
| 8773 | LENS GASKET | 2 | License lamps |
| 164-060 | HEADLAMP GASKET | 2 | Seals headlamp unit to body |
| 38-00232 | OVER RIDER SEAL | 6' | Seal between over riders and bumpers |
| BD20903/1 | COWL SEAL | 1 | Cushions rear edge of bonnet, glued into channel near base of windshield |
| 8608 | FRONT LAMP PADS | 1 PR | Pad between front lamps and body |
| 8608 | FRONT LAMP PADS | 1 PR | Pad between front lamps and body |
| 8624/6 | REAR LAMP PADS | 1 PR | Pad between rear lamps and body |
| BD25716/7 | A-POST SEAL, PAIR | 1 PR | Major seal for leading edge of doors; glued to body (See Note #3) |
| BD20499 | WINDSHIELD SEAL | 1 | Holds windshield in place -- requires locking strip below (See Note #4) |
| BD20499-1 | W/S LOCK STRIP | 10' | Fits in channel of windshield seal; expands it to make tight seal |
| 38-2020 | CHANNEL FELT | 8' | For door glass channels. Push in to channels and trim flush. |
| 38-2024 | DOOR FRAME RUBBER SEAL | 3' | Leading edge of door frame; fits in channel; 1.5' required per side. |
| BD35729 | HEADLAMP FINISHER SEAL | 2 | Seal under headlamp chrome finishers (See Note #5) |
| BD16700 | WINDOW SEAL | 2 | Squeegee seal; between door and outer surface of door glass. Clips in place |
| BD20010/3 | 24 inch FUZZY STRIP | 2 | Fuzzy seal; between door and inner surface of door glass, clips in place |
| 8656 | BEZEL PAD | 3 | Under chrome windshield wiper bezels |
| BD20434 | MUDSHIELD SEAL | 6' | Mud shields under bonnet; riveted in place |
Notes
1: These were fitted to the rear of later cars, but many customers prefer to fit them at all attaching points. Use as you see fit.
2: We liberally coat this and the chrome with WD40, install chrome and clamp. Trim flush the next day. The WD40 acts as a solvent
3: A coupe A-Post seal is supplied. Cut for roadster.
4: A coupe windshield seal is supplied. Cut for roadster.
5: Does not have pre-drilled holes; customer must drill holes for attachment rivets.
Note: This item replaces part number 18-0518.
| Model (Site) | Category | Schematic | Key | Name | Application | Qty |
|---|---|---|---|---|---|---|
| Jaguar E-Type | Body Fittings | Body Rubber Kits | 1 | BODY RUBBER KIT | E-Type Series 1.5 OTS | 1 |
The Longest in the Business
- All Classic British products are warrantied to be free from defects in material and workmanship for 2 years from the date of invoice.
- All superchargers, supercharger components, and supercharger hardware are warranted to be free from defects in material and workmanship for 1 year from date of invoice.
- Moss Motors, Ltd. will, at its discretion, repair or replace any part that fails in service within the warranty period. This warranty does not cover labor, failure of related components, normal wear of brake or clutch components or failure resulting from alteration, misuse, accidental damage, faulty installation, or faulty repair.
- Warranty requests should be submitted to our sales department and must be supported by the original Moss Motors purchase invoice and documentation of the failure.
Product Name:
Body Rubber Kit
Make:
Jaguar
Model:
E-Type
Year:
1968